Фильтр внешний sunsun hw 302 инструкция

HW-302-304 External Aquarium Filter
User Manual

Картинка с сайта: manualspro.net

HW-302-304 External Aquarium Filter

HW-302–304, 402B–404B, 403A, 404A
50192–50197, 50358, 50359
Illustrations similar may vary depending on the model:
Read and follow the operating instructions and safety information before
using it for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps, and technical
data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities,
please contact us.
** The information contained in this document may alter at any time without
previous notice. It is prohibited to copy or spread any parts of this document
in any way without prior written allowance. All rights reserved.
The WilTec Wildanger Technik GmbH cannot be held accountable for any possible
mistakes in this operating manual, nor in the diagrams and figures shown.
Even though the WilTec Wildanger Technik GmbH has undergone the biggest
possible efforts to ensure that the operating manual is complete, faultless,
and up to date, mistakes cannot be entirely avoided. If you should find a
mistake or wish to make a suggestion for improvement, we look forward to
hearing from you.
Send an e-mail to: service@wiltec.info
or use our contact form: https://www.wiltec.de/contacts/
The most recent version of this manual in various languages can be found in
our online shop via: https://www.wiltec.de/docsearch
Our postal address is: WilTec Wildanger Technik GmbH
Königsbenden 12 52249 Eschweiler Germany
To return orders for exchange, repair, or other purposes, please use the
following address. Attention!
To allow for smooth execution of your complaint or return, it is important to
contact our customer service team before returning the goods.
Returns Department**
WilTec Wildanger Technik GmbH Königsbenden 28
52249 Eschweiler
E-mail: service@wiltec.info
Tel: +49 2403 55592–0
Fax: +49 2403 55592–15

Introduction

Thank you for purchasing this quality product. To minimize the risk of injury
we urge that our clients take some basic safety precautions when using this
device. Please read the operation instructions carefully and make sure you
have understood its content. Keep these operation instructions safe.
Safety instructions

• The appliance has only been designed for aquarium and indoor use.
• To avoid possible electric shock, special care should be taken since water is employed in the use of this appliance. Do not attempt to repair it by yourself. Return the appliance to the authorized service facility for maintenance or discard it.
• Make sure that your outlet voltage corresponds to the stated voltage on the pump rating label.
• If the appliance is submerged in the water, DO NOT reach for it! Cut the power supply FIRST and then touch it.
• Carefully examine the appliance after installation. It should not be plugged in if its electrical components are wet.
• Do not operate any appliance with a damaged cord or plug, or with a cord or plug in an abnormal state. The supply cord of the appliance cannot be replaced. If the cord is damaged, the appliance should be scrapped.
• Make sure that the electrical cord loops form a “drip loop” below the electrical outlet. The use of a drip loop will help prevent any water leaks or splashes from running down the electrical cord into your outlet. Instead of any water getting into your outlet, it will simply drip off the cord at the lowest point in the loop.
• Close supervision is necessary when the appliance is used by or near children.
• Always unplug the appliance when not in use, before putting on or taking off parts, and before cleaning.
• Do not install or store the appliance where it is exposed to moisture or to temperatures below freezing.
• Make sure the appliance is securely installed before operating it.
• Read and observe all the instructions supplied with the appliance and on the appliance.
• The pump must not run dry.
• Never use accessories that are not recommended by the appliance manufacturer. It may result in fire,  electric shock, and/or personal injury.
• Use the appliance ONLY for domestic purposes and in the way indicated in these instructions and place it in a dry environment.

Installation

1. To set your filter up, the buckles (1) and (2) should be unclipped from the main body of the filter head; this will then separate the filter head from the filter base.”

2. You can then access your filter trays to clean the filter media or add filter media. Repeat step one to refasten the filter head to the filter base.* UV unit depends on the model.

3. Push the inlet and outlet taps into the filter head and fasten using the small handle in between the taps; this is also the valve shut. After this, attach a hose to each tap and secure using the screw taps.

   

   Картинка с сайта: manualspro.net

4. According to the diagram, then attach the input downpipes and output spray bars according to the diagram.

   

   Картинка с сайта: manualspro.net

5. Then press down the primer button on top of the filter head; this will prime the filter drawing water in through the hose. Repeat, if necessary, until the entire pipework is filled with water.

   

   Картинка с сайта: manualspro.net

6. The switch (3) to turn on and off the UV and indicator is on the filter side. Please check the UV regularly when cleaning your filter to make sure it works best.

   

   Картинка с сайта: manualspro.net

7. Under any condition, when the filter base is separated from the filter head, the protect switch will turn off the device. Then the UV will be extinguished to avoid any filter base damage.

Replacing the UV light tube
Applies only to models equipped with a UV unit

Картинка с сайта: manualspro.net

1. According to the diagrammatic presentation (1), carefully open the filter basis lid. Take off the lid and reverse it, then hold the quartz tube and lightly turn it clockwise, just as the picture shows.

2. When the quartz hose tube gap and the light tube connection gap are accordant, pull out the quartz tube.

   

   Картинка с сайта: manualspro.net

3. Pull out the old light tube.

4. Install the new light tube and the quartz tube.

   

   Картинка с сайта: manualspro.net

Technical data

Item| Model| UVC power
(W)| Output
CA )| Transportation
height (m)| Weight
(kg)| Cable length
(m)| Dimensions
(mm)| Baskets
(number)
—|—|—|—|—|—|—|—|—
50197| NW-302| —| 1000| 1.| 4.| 2.| 28o x 28o x 430| 3
50195| HW-3o3| —| 1400| 2.0| 5.| 2.| 25o x 25o x 43o| 3
50193| HW-3o4| —| 2000| 3.| 6.| 2.| ego x ego x 480| 4
50196| HW-4o2B| g| woo| 1.| 4.| 2.| 230 x 23o x 390| 3
50194| HW-4o3B| 9| 1400| 2.0| 5.0| 2.| 25o x 25o x 43o| 3
50192| HW-4o4B| g| 2000| 3.| 6. o| 2.| 300 x 300 x 450| 4
50359| HW-4o4A| —| 2000| 3.| 9.0| 2.| 300 x 300 x 450| 4
50358| HW-4o3A| —| 1400| 2.0| 8. o| 2.| 25o x 25o x 43o| 3

Energy supply: 220–240 V AC, 50 Hz,
Protection type : IP44
**Operation and troubleshooting***

water side is the input side.
The motor does not operate.| Power off| Turn on the power.
Shaft break| Replace shaft.
Impeller missing or motor blocked due to foreign materials such as pebbles and
shells| Set impeller, clean outdrive system.
Waterflow inhibited| The Hose adapter is very dirty| Dismantle hose adapter
unit,
clean the interior with a brush.
Incorrect tube connections| Check if tubes are entangled or crimped
Excessive dirt build-up in hoses| Periodically clean the inside of hoses,
intake, and pipes.
Filter material plugged| Remove filter material, and wash with water from the
tank.
Abnormal sound when starting fil- ter| Air entering from the hose connection|
Check if hose connections are airtight.*
Air remaining inside filter case| Leave power on; slightly shake the filter to
remove the remaining air.
Abnormal sound while operating filter| Dirty, displaced, or distorted 0-
rings.| Control all 0-rings if seated at the correct position, and carefully
clean them if necessary.
Air remains inside the filter.| Slightly shake filter basis several times to
remove remaining air.
Damaged impeller/drive magnet or spindle| Replace damaged piece.
Water too dirty| Clean away dirt.

• Further notes on maintenance, cleaning, and troubleshooting are to be found next.

Filter operation and troubleshooting

Noise reduction/external air
Especially the suction intake and the connected suction surface must be
checked for tightness and to be adjusted according to the aquarium water
level. If this is not possible due to aquarium technical reasons, seal the
whole suction surface so that no external air can get into the filter.
Evacuating air from filter system Take the return-flow hose that conducts the
water from the filter to the tank and put it into a clean bucket that is
placed below the filter. Leave the hose inside the bucket and carry out the
deaeration process (evacuate the air) by activating the manual pump. Please
make sure that the potential flow is adjusted to the inlet-outlet connector.
As soon as no air bubbles can be seen, seal the hose with a finger and install
it again on the return pipe at the top edge of the aquarium as intended.
Leakage after installation or cleaning If a slight leakage still persists
after the filter installation or the filter cleaning, the problem is most
likely the sealing between the hose connector adaptor and the filter head
(cover lid). The plug-in adaptor that the hoses are connected to has two
O-rings on the lower side that seal the connection inside the filter lid. If
these O-rings are dirty, displaced (out of place), or damaged, they cannot
seal properly anymore and water escapes into the filter lid/aquarium filter
cover. The leak point is then the lowest point of the filter cover/lid and
appears typically at the lateral clamping points that connect the cover lid
with the filter basis.
The remedy is here as simple as the failure itself. You must rinse and check
the O-rings. Make sure that the spots where the O-rings must be inserted and
positioned are free of dirt. On these particular spots, algae formation can
appear and impair or damage the O-rings sealing if no regular cleaning is
carried out. This problem can also appear in the case of a new installation
because of sand, for instance.
Please allocate sufficient time for rinsing and cleaning; if this is not done
carefully and thoroughly, the aquarium canister filter may still leak after
the O-ring sealings have been cleaned. If despite thorough cleaning, the water
leakage at the spots above-mentioned still persists, you must check the O-ring
seating inside the adaptor.
This requires opening the inlet/outlet adapter. Please contact our customer
service agents who are looking forward to helping you.

Parts list

Картинка с сайта: manualspro.net

Картинка с сайта: manualspro.net

Basics – Filter media
The delivered filter media represents only the basic filter material needed
for your aquarium.
Please inform yourself regarding what filter materials are suitable for your
aquarium because these can differ depending on the fish and plants living
there.
Please use one filter cotton for only one filter stage. This should be
regularly renewed because dirty filter cotton can quickly lead to a decrease
in filter efficiency.
Aquarium external filters consist of several layers. The water sucked in is
filtered in several stages. The lowest layer consists of bio balls. These
balls offer bacteria a large settling area and retain coarse dirt. Above that,
a layer of ceramic rings should follow. On the top level, we recommend a
filter sponge covered with filter cotton. (This is an example; please adapt it
to your practical aquarium.)
Additionally, and temporarily, you can place here another layer of activated
carbon (in a net or partly available as a filter mat), and this will one of
the filter layers. This should not be permanent but only be used after a
medication treatment and for turbid water with suspended particles. (Not
included.)
When you purchase a new aquarium filter or after it has been fully cleaned,
the useful bacteria must be enriched again. For this reason, there are special
bacteria cultures that can be supplied in the aquarium to facilitate their
settlement. Basically, put the filters from bottom to top as follows:
1st stage: mechanical/semi-biological filtering
2nd stage: biological filtering
3rd stage: chemical filtering (activated carbon, peat, phosphate, etc.)
If necessary, the aquarium filter can be extended to 4 stages by adding a
mechanical or biological filter stage.
Disposal regulations
EU guidelines regarding the disposal of scrap electric appliances (WEEE,
2012/19/EU) were implemented in the law related to electrical and electronic
equipment and appliances. All WilTec electric devices that fall under the WEEE
regulations are labeled with the crossed-out wheeled waste bin logo. This logo
indicates that this electric equipment must not be disposed of with domestic
waste.
The company WilTec Technik GmbH has been registered in the German registry EAR
under the WEEEregistration number DE45283704.
Disposal of used electrical and electronic appliances (intended for use in the
countries of the European Union and other European countries with a separate
collection system for these appliances).
The logo on the article or on its packaging points out that this article must
not be treated as normal household waste but must be disposed to a recycling
collection point for electronic and electrical waste equipment. By
contributing to the correct disposal of this article you protect the
environment and the health of your fellow men. Environment and health are
threatened by inappropriate disposal.

Картинка с сайта: manualspro.net

Material recycling helps reduce the consumption of raw materials.
Additional information on recycling this article can be provided by your local
community, municipal waste disposal facilities, or the store where you
purchased the article.
Address:
WilTec Wildanger Technik GmbH
Königsbenden 12 / 28
D-52249 Eschweiler
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even in
part, of this instruction manual, require the written permission of WilTec
Wildanger Technik GmbH.

****© by WilTec Wildanger Technik GmbH
Item 50192–50197, 50358, 50359
http://www.WilTec.de
http://www.aoyue.eu
http://www.teichtip.de

References

• Aoyue.de
• Teichtip.de
• WilTec — Ihr Online Shop für Haus, Garten, Werkstatt, Freizeit
• WilTec Wildanger Technik GmbH

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>