Робот пылесос roidmi eve plus robot vacuum and mop cleaner with cleaning base инструкция

ROIDMI Eve Plus Robot Vacuum and Mop CleanerSafety instructions

Read this operation manual before using the product
Warning: To avoid injury to yourself and others, and to avoid unnecessary
property damage, read carefully before using the product and observe the
following “Safety instructions”. The safety instructions are divided into two
sections, “Warning” and “Caution”. The “Warning” and “Caution” sections
contain important information for safe use of the product and must be
followed.
Hereby, [ROIDMI INFORMATION TECHNOLOGY CO., LTD.] declares that the radio
equipment type [2.4GHz WLAN Module] is in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity is available at
the following internet address:http://doc.roidmi.com/web/#/27?page_id=0

Warning

Instructions against incorrect product use that may lead to death or serious
injury

Caution

Instructions against incorrect product use that may lead to minor injury or
product damage

Warning

1. Do not use this product in wet places such as bathrooms or near water sources.
2. Do not use it to clean up liquids, matches and wet garbage.
3. Do not pull or insert the plug, or touch the adapter socket with wet hands.
4. Do not use damaged power plugs and loose sockets.
5. Do not use the main unit to clean flammable liquids such as kerosene, gasoline, objects with sparks, toner cartridges, toner and other combustible dust; do not use the device near the above items, or in environments with flammable and explosive gases to avoid fires.
6. Do not disassemble, repair, or modify the product on your own, to avoid fire, injury, or damage, except for the replacement of consumables in accordance with this manual.
7. When using the adapter, use an AC power supply with a correct rated voltage, and do not use a generator or DC power supply to avoid fire or electric shock. Do not charge non-rechargeable batteries.
8. Use a dry cloth to clean the dust on the plug regularly to avoid fires due to poor insulation or other reasons.
9. Be sure to insert the plug firmly and completely into the socket to avoid electric shock, short circuiting or fire.
10. In the event of an abnormal fault, cut off the power immediately and stop using the product to avoid smoke, fire or electric shock.
11. When charging or using the product, if the product’s body becomes deformed or is unusually hot, gives off a burning smell, or emits abnormal noises while operating, immediately cut off the power and unplug the plug. Then
12. place the product in an open area away from any combustible materials to ensure safety. Have the manufacturer or authorized maintenance personnel replace or maintain the product to avoid danger.
13. Be sure to unplug the plug from the power socket before cleaning and maintenance to avoid electric shock or injury.
14. If you find that the main brush is abnormal during use, turn off the power and immediately check whether the main brush is entangled with hair or other long fibers, and clean it in a timely manner.
15. Do not spray water on the product body and plug, or immerse them in water.
16. Do not use other adapters to charge the main unit.
17. When unplugging the plug, be sure to hold the insulated part of the adapter body. Do not pull the power cord.
18. The battery is a sealed device, and does not pose a safety hazard under normal circumstances. If liquid leaks out of the battery under extreme conditions, it may cause irritation or burns. If you accidentally come into contact with the liquid, take the following instructions:
19. In case of skin contact – wash with soap and water;
20. IN case of eye contact – rinse immediately with water for at least 15 minutes and seek medical help.
21. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved
22. Keep the robot vacuum and mop cleaner away from electromagnetic equipment in hospitals. This product is not a toy. Do not allow children to play with it. Use this product only with accessories supplied with it.cleaning and user maintenance shall not be made by children without supervision
23. The adapter is for indoor use only, do not expose it to rain.
24. If the exterior is damaged, do not use the adapter to avoid risk of electric shock.
25. This adapter is only intended for use with designated robot vacuum and mop cleaners.
26. Before charging, check whether the adapter specifications conform with the required power supply voltage.
27. Before disposing of the appliance, the battery must be removed from the appliance.
28. This appliance incorporates an earth connection for functional purposes only.
29. The supply connection of dust collector is appliance inlet.The cross-sectional area of supply cord used for the appliance at least 0.75mm².

Caution

1. Do not use this product outdoors, on surfaces other than the ground, or in commercial or industrial environments.
2. Do not use the product in environments without protective fencing (such as duplex floors, open balconies, furniture tops).
3. Do not block the air outlet (so as to avoid deformation, product failure, or fire due to overheating).
4. Do not drag the product body (so as not to scratch the ground).
5. Do not shake or let children play with the product body (so as to avoid injury or damage to the product body).
6. Do not drop the product, bump it against other objects, or apply pressure to the product (so as to avoid fire or electric shock due to product failure).
7. Be sure to install the main brush and filter before use (so as not to cause damage to the motor or product body).
8. Check if the power cable is in good condition before charging the product.
9. Before using the robot vacuum and mop cleaner for the first time or replacing the specified filter, turn off the power on the main unit and make sure that the filter is properly installed.
10. Used battery packs should be properly disposed off. Do not discard them randomly.
11. Before using the product, arrange the desks, chairs, household items, floor objects, etc. neatly, and clear power cords and small items laying on the ground to avoid the product being blocked during cleaning.
12. When the machine is running, keep curtains and tablecloths away from the ground, and keep the carpet flat, so as to prevent the product from being blocked during operation and causing damage to your valuables.
13. Be sure to open the door of each room before the first use, so that the product can build a complete home map.
14. Do not stand in front of the main unit when the appliance is running, to prevent the main unit from being unable to recognize the area to be cleaned.
15. Do not use and store the main unit under extreme adverse conditions, such as extreme temperatures. It is recommended to use it indoors. Store it in a cool and dry place.
16. Do not use the adapter and dust collector to recharge non-rechargeable batteries.16.Do not use the adapter and dust collector to recharge non-rechargeable batteries.16.Do not use the adapter and dust collector to recharge non-rechargeable batteries.

Product overview

Main unit

Картинка с сайта: manualspro.net

Electric water tank and mopping module

Картинка с сайта: manualspro.net

Картинка с сайта: manualspro.net

Dust collector (optional)

Картинка с сайта: manualspro.net

Working principle of dust collection station
The dust collection station always emits infrared signals at a certain angle
and distance. When the sweeper detects the infrared signal during the
recharging process, it will travel to a certain distance directly in front of
the dust collection station, adjust the angle and retreat to the dust
collection station. When the dust collection conditions are reached, the dust
collection station starts to collect dust. After the dust is collected, the
deodorizing ion generator starts to work to deodorize, and at the same time it
starts to charge. If the dust collection condition is not reached, charge
directly and the display shows the real-time power.
Charging dock (optional)

Картинка с сайта: manualspro.net

Product installation and charging method

Installation and use of dust collection station (optional)

1. Step 1: Place the dust collection station according to the position and distance shown in the figure, and connect the “pin end” of the power cord to the body of the dust collection station, and the “metal plug end” to the wall power supply, as shown in the figure；
2. Step 2:When the power supply and the dust collection station are normally connected and energized, long press the power button of the sweeper to turn on and use. When the sweeper robot consumes power, it can recharge by itself, or manually short press the recharge button to recharge and charge.
   

   Картинка с сайта: manualspro.net

Caution

1. When charging, do not install the mopping module to prevent water seeping from the wet mop and damaging the floor.
2. Do not use this product in the room of infants and young children, keep it away from infants and young children.
3. When the main unit is docked at the dust collector, do not let children or pets approach it or collide with the main unit to avoid danger.
4. In order to facilitate the smooth return of the main unit to the dust collector after cleaning, it is recommended to start the appliance from the dust collector and that you do not move the dust collector during the cleaning process.
5. The dust collector has dust collection and charging functions, and a new dust bag is installed before the product leaves the factory.
6. Please make sure that the power supply and the dust collection station are normally energized before the sweeping robot can be charged. The dust collection station that is not connected to the power supply does not have the charging function.

Installation and use of recharger (optional)

1. Step 1: Place the rechargeable cradle according to the position and distance shown in the figure, connect the round plug of the adapter to the rechargeable cradle body, and connect the “metal plug end” to the wall power supply, as shown
   

   Картинка с сайта: manualspro.net

2. Step 2: When the adapter and the recharger are normally connected and powered on, press and hold the power button of the sweeper to turn on and use it. When the sweeper robot consumes power, it can recharge by itself, or manually short press the recharge button to recharge and charge ；
   

   Картинка с сайта: manualspro.net

Caution

1. When charging, do not install the mopping module to prevent water seeping from the wet mop and damaging the floor.
2. Do not use this product in the room of infants and young children, keep it away from infants and young children.
3. When the main unit is docked on the charging dock, do not let children or pets approach it or collide with the main unit to avoid danger.
4. In order to facilitate the smooth return of the main unit to the charging dock after cleaning, it is recommended to start the appliance from the charging dock and that you do not move the charging dock during the cleaning process.

Installing the mopping module

1. Step 1: Attach the mop
   Stick the mop on the designated area on the mop holder

2. Step 2: Add water to the water tank
   Open the lid of the electric dust collecting tank, and close the lid of the
   electric dust collecting tank after filling with water

3. Step 3: Install the water tank
   Push the electric water tank and dust box horizontally in the direction of the
   groove on the main unit until you hear a “click” sound.

   

   Картинка с сайта: manualspro.net

4. Step 4: Install the mopping module
   Push the mopping module buckle in parallel along the electric water tank until
   you hear a “click” sound.

   

   Картинка с сайта: manualspro.net

Caution

1. Do not use the mopping function on the carpet.
2. When charging or when the robot is not in use, remove the mopping module, pour out the excess water in the water tank and clean the mop to avoid mold or odor.
3. It is recommended to clean the mop each time to maintain water speed and cleaning effect. Replace with a new mop if necessary.
4. When charging the main unit on wooden floors, remove the mopping module in a timely manner to prevent water seeping from the mop and damaging the floor.\

Use

Downloading app
This product is compatible with the ROIDMI vacuum cleaner platform, and can be
controlled using the “ROIDMI” app. It supports Android and iOS systems.

1. Scan the QR code below, or search for “ROIDMI” in the app store to download and install the app.
2. Sign in to the app. Long press and buttons on the robot cleaner at the same time for longer than 3 seconds to reset it. Click “+” at the upper right on the app’s homepage to add device. Select the robot cleaner from the device list and connect it to WiFi according to the prompts.
   

   Картинка с сайта: manualspro.net

3. If you have any question, please contact our service personnel or visit our official website. * This product only supports 2.4G WiFi

Mi Home app

This product works with mijia (Mi Home). It can be controlled via Mi Home app
and interconnected with other smart devices.

1. Scan the QR code below, or search for “Mi Home” in the app store to download and install the app.
2. Turn on Mi Home app, register an account or sign in to the app.
3. Long press and buttons on the robot cleaner at the same time for longer than 3 seconds to reset it. Click “+” at the upper right on the app’s homepage to add device.
4. In the device category list find the “Robot Cleaner” category, then click your ROIDMI robot cleaner model to enter Network Configuration interface.
5. Perform follow-up operations according to the app’s prompts on network configuration.
   

   Картинка с сайта: manualspro.net

Reminder: Actual operations may vary due to upgrade and update of Mi Home
app. Please follow the instructions in the app.
Please note that “works with mijia” only certifies the product is compatible
with Mi Home app. Xiaomi and Mijia are not liable for any problems related to
the product itself and its manufacturer’s production, executive standards,
quality control, etc.

• Some overseas regions do not support connection to Mi Home APP

Turning on/off and cleaning modes

1. Turning on/off
   Press and hold the Power button, the Power button indicator is ON and the main
   unit enters Standby mode. When the main unit is in Idle mode, press and hold
   the Power button, the indicator slowly turns off and the cleaning cycle is
   done.
   When the main unit is running, press any button to pause the appliance. Press
   the Power button again to resume the cleaning cycle.
   Press the Dock button, the main unit automatically docks and the cleaning
   cycle will end. Press the Spot button to clean a localized area.

2. Charging
   When a cleaning cycle is complete, the main unit automatically docks and
   charges itself. If an error occurs, resolve the problem and press the Dock
   button after troubleshooting, the main unit automatically docks.
   When the main unit is charging, the Power button indicator is always ON; when
   fully charged, the indicator breathes (breathe = dim and brighten at a certain
   rate).
   If a cleaning cycle does not start from the charging dock or dust collector,
   the robot may fail to dock. When the cleaning cycle is complete, the main unit
   automatically returns to where it started. To return it to the charging dock
   or the dust collector, press the Dock button.

3. Clean mode
   After the main unit is turned on, it scans and intelligently maps out a series
   of areas. Then it cleans along the wall and then in small arcs until the area
   is complete. When the cleaning cycle is complete, the main unit automatically
   returns to the charging dock or the dust collector.
   Press the Power button to start a cleaning cycle. The cleaning path is as
   shown in the figure below. Press any button to pause the cleaning.

   

   Картинка с сайта: manualspro.net

   

   Картинка с сайта: manualspro.net

4. Cleaning a localized area When the main unit is in Standby mode or paused, press the Spot button to start cleaning a localized area. The cleaning area is a 1.6 m x 1.6 m square centered on the main unit. After cleaning, the main unit automatically docks.

5. Room mode
   If a room has been set in map management, select the room and press the Spot
   button to clean it. If not set, firstly set the room boundaries on the APP.

6. Adding water or cleaning the mop while operating
   In Operating mode, to add water or clean the mop, press the Power button to
   pause the main unit, remove the dust box + water tank (2 in 1) and the mopping
   module. When finished, reinstall them back, and press the Power button to
   resume the cleaning cycle.

7. Error symptom
   When an error occurs while the main unit is operating, the Power button
   indicator flashes quickly and a voice prompt will be heard. Refer to the
   “Troubleshooting” section in this manual to resolve the problem.

8. Sleep mode
   After 1 0 minutes of no operation, the main unit automatically enters Sleep
   mode. Press any key to wake it up.

9. WiFi reset
   When resetting the password or when your phone is unable to connect to the
   main unit for other reasons, reset the WiFi according to the instructions in
   “APP downloads” section of this manual.

10. Automatic dust collection (only applicable to robot vacuum and mop cleaner supplied with a dust collector) When a cleaning cycle is complete, the robot automatically returns to the dust collector for charging and dust collection.

11. Reset button
    When the button does not respond or cannot be turned on, please try to reset
    the system; after reset, the timing cleaning setting and cleaning mode setting
    of the host will be cleared. Set WiFi.

Caution

1. It is recommended to start cleaning when the main unit is on the charging dock or the dust collector.
2. When power is insufficient during cleaning, the main unit will automatically dock on the charging dock or the dust collector and charge itself. It will return to where it left off and resume cleaning after charging is completed.
3. Before using the product, arrange the desks, chairs, household items, floor objects, etc. neatly, and clear power cords and small items laying on the ground to avoid the product being blocked during cleaning.
4. Do not stand in front of the main unit when the appliance is running, to prevent the main unit from being unable to recognize the area to be cleaned.
5. After the main unit has finished working, it is recommended not to shut it down, and to keep the main unit in the charging state so it can better carry out the next cleaning task.

Turning on/off and operating the dust collector (optional)
Touch the LED display to turn on the dust collection function. When the dust
collection function of the integrated station is normal, the outer ring
indicator light shows the state of the running water light, and the smell ion
generator indicator light is always on for 30 minutes and then goes out. The
LED display will also display the remaining power; if the dust bag is not
installed, the fault code will be displayed; in addition, the display There
are also functions for reminding the work of the smell ion generator, the
communication light of the dust collection station and the host, and the
function of reminding that the dust is full.

Картинка с сайта: manualspro.net

Dust collector status indicator

Status

|

Outer ring indicator

|

Power level indicator

|

Deodorant ion indicator

| Communication signal indicator|

Dust full reminder

—|—|—|—|—|—
Initializing| | 888| | |
Main unit in place/dust collector functions well| | | | |
Main unit absent/dust collector functions well| | | | |
Collecting dust| | 012    001| | |
Normal suction during dust collection| | | | |
Abnormal suction during dust collection| | 001| | |
Dust bag full/main unit in place| | | | |
Dust bag full/main unit absent| | | | |
Dust bag not installed/main unit in place| | 000| | |
Dust bag not installed/main unit absent| | 000| | |
Communication is abnormal/host is in place| | 004| | |
Powered off/indicators turned off via APP| | | | |
Remarks:  indicates blinking;        indicates off;       indicates constant
on

Reminder: Make sure the dust collector is connected to the power supply
and the main unit is in place, so that you can start cleaning and dust
collection remotely at any time through the APP.

Cleaning and maintenance

Always turn off the product before any maintenance!
Disassembling and installing the main brush

1. Step 1: Disassemble the main brush
   Turn the robot vacuum and mop cleaner over, press the main brush cover release
   button to remove the main brush cover. Take out the main brush and clean it
   .

   

   Картинка с сайта: manualspro.net

2. Step 2: Clean the main brush
   Use the cleaning brush to pick up and cut away the hair and fibers entangled
   on the main brush. It is recommended to replace the main brush every 3-6
   months.

   

   Картинка с сайта: manualspro.net

Caution

1. Turn off the product before replacing the main brush.
2. The cleaning brush has a sharp blade, which is used to cut away entangled objects that are difficult to clean. Keep the cleaning brush away from children.

Disassembling and installing the side brush

1. Step 1: Disassemble the side brush
   Turn the robot vacuum and mop cleaner over, remove the screw with a
   screwdriver, and take out the side brush.

   

   Картинка с сайта: manualspro.net

2. Step 2: Clean the side brush
   Use the cleaning brush to pick up and cut away the hair and fibers entangled
   on the side brush. It is recommended to replace the side brush every 3-6
   months to ensure effective cleaning.

   

   Картинка с сайта: manualspro.net

Caution

1. Only replace with a side brush supplied by ROIDMI, otherwise, it may lead to damage to the main unit.
2. To avoid scratching yourself, be careful when using a screwdriver to replace the side brush.
3. Install the left and right side brushes correctly onto their respective pins.

Disassembling and installing the dust box + water tank (2 in 1) and
filter

1. Step 1: Disassemble the dust box + water tank (2 in 1)
   Press the dust box + water tank (2 in 1) release button to remove the dust box

• water tank (2 in 1).

  

  Картинка с сайта: manualspro.net

  1. Step 2: Disassemble the filter
     Press the filter release button on the right of the dust box + water tank (2
     in 1) to remove the filter.

     

     Картинка с сайта: manualspro.net

  2. Step 3: Empty the dust box + water tank (2 in 1)
     Align the dust box with the opening of a trash can and empty the dust. Use the
     cleaning brush to clean the dust box corners that are hard to reach.

     

     Картинка с сайта: manualspro.net

  3. Step 4: Clean the dust box + water tank (2 in 1)
     Rinse the dust box + water tank (2 in 1) with clean water. Air-dry completely
     for at least 24 hours before reinstalling to prevent dust from clumping during
     the next use.

     

     Картинка с сайта: manualspro.net

Disassembling and installing the mop

1. Step 1: Disassemble the mop
   Remove the mopping module from the dust box + water thank (2 in 1), and remove
   the mop from the mopping module.

   

   Картинка с сайта: manualspro.net

2. Step 2: Clean the mop
   Rinse the mop with clean water. Air-dry completely before reinstalling to
   prevent dust from clumping during the next use.

   

   Картинка с сайта: manualspro.net

Caution

1. Only replace with a mop supplied by ROIDMI, otherwise, it may lead to ineffective cleaning.
2. Be sure to remove and clean the mop to prevent dirty water flowing back.
3. It is recommended to replace the mop every 3-6 months to ensure effective cleaning.

Cleaning the replacement parts

1. Step 1: Clean the sensors
   Use a soft clean cloth to wipe and clean the charging plates on the back, the
   laser distance sensor on the top, the edge sensors, the infrared docking
   sensors and the TOF wall tracking sensor.

   

   Картинка с сайта: manualspro.net

2. Step 2: Clean the universal wheel
   Turn the robot vacuum and mop cleaner over and pull out the universal wheel,
   clean out the hair and dirt from the wheel and axle. Wash the universal wheel
   with water, air-dry completely and reinstall it.

3. Step 3: Clean the filter
   Rinse the dust box filter with clean water. Air-dry completely before
   reinstalling to prevent dust from clumping during the next use.

   

   Картинка с сайта: manualspro.net

Clean the charging dock (optional)

1. Step 1: Clean the charging contact
   Check whether there is dirt on the charging contacts. Wipe and clean the
   charging contacts with a soft clean cloth to keep it clean and free of debris
   .
   

   Картинка с сайта: manualspro.net

Caution

1. Use a dry cloth to clean the main unit’s sensors, infrared sensors and charging contacts. Do not use a wet cloth to prevent water from entering the appliance and causing damage.
2. To avoid scratching yourself, be careful when using a screwdriver to replace the replacement parts.

Clean the dust collector (optional)

1. Step 1: Replace the dust bag
   When the dust bag is full, the dust full indicator on the LED display of the
   dust collector becomes constant on, replace the dust bag. It is recommended to
   replace the dust bag every 4 weeks.

   

   Картинка с сайта: manualspro.net

2. Step 2: Clean the dust channel
   If the dust collector does not work while powered on and the dust bag is not
   full, firstly disconnect it from the power supply and check whether the dust
   channel is blocked. If it is blocked, use a screwdriver to open its
   transparent cover and clear out the obstructions.

   

   Картинка с сайта: manualspro.net

3. Step 3: Clean the infrared lens and charging contacts
   Wipe and clean the infrared lens and charging contacts with a soft clean cloth
   to keep it clean and free of debris.

   

   Картинка с сайта: manualspro.net

4. Step 4: Clean the fan filter bracket
   Check whether the fan filter bracket is entangled with any foreign objects or
   debris. Wipe with a soft clean cloth to keep it clean and free of debris
   .

   

   Картинка с сайта: manualspro.net

Caution

1. Use a dry cloth to clean. Do not use a wet cloth to prevent water from entering the appliance and causing damage.
2. To avoid scratching yourself, be careful when using a screwdriver to replace the replacement parts.

Troubleshooting

When an error occurs while the robot vacuum and mop cleaner is operating, the
Power button indicator flashes quickly and a voice prompt will be heard. Refer
to the “Troubleshooting” table below to fix the error.

Error message

|

Solution

—|—

Error 1:

Check if the radar is obstructed or stuck. If it is, move the main unit to a
new location and start it.

| If the radar is obstructed or stuck, remove the obstruction or debris.
Do not use the product outdoors under sunlight or in places with strong light.
Use it indoors.
If the solutions above do not work, move the main unit to a new location and
start it.
If the alert continues, contact the customer service.

Error message

|

Solution

—|—

Error 2: Check if the bumper is stuck.

| If the bumper is stuck, remove the debris and briskly tap the bumper several
times to dislodge any debris that may be trapped underneath.
If the product is trapped because of insufficient space, move it to a new
location and start it.
If the alert continues, contact the customer service.

Error 3: Wipe the edge sensor, move the main unit away from edge and start it.

| If the main unit is suspended in the air, move it to a new location and
start it.
If the edge sensor is dirty or obstructed by debris, clean the edge sensor
regularly.
If the alert continues, contact the customer service.

Error 4: Check if the main brush is stuck.

| If the main brush is entangled with wool, wires and other debris, remove the
main brush and clean it.
Clean up wool, wires and other debris on the floor.
Regularly clean the main brush, as it can easily be entangled with debris.
If the alert continues, contact the customer service.

Error 5: Check if the side brushes are stuck.

| If the side brushes are entangled with wool, wires and other debris, remove
the side brushes and clean them.
Clean up wool, wires and other debris on the floor.
Regularly clean the side brushes, as they can easily be entangled with debris.
If the alert continues, contact the customer service.

Error 6: Check if the driving wheel is stuck.

| If the driving wheel is stuck, clean it.
If the alert continues, contact the customer service.

Error 7: Reinstall the dust box + water tank (2 in 1).

| Reinstall the dust box + water tank (2 in 1) and filter and make sure they
are reinstalled properly.
If the error persists, replace the filter.
If the alert continues, contact the customer service.
Error 8: Battery is too low, please charge.| Battery is low, charge it before
use.
Error 9: Cannot charge. Check if the main unit is correctly connected to the
dust collector.|

Use a dry clean cloth to wipe the charging contacts on the dust collector and
the charging plates on the main unit.

Error 10: Battery pack temperature is too high or too low, try it again
later.| If battery temperature is too high or too low, use the appliance when
its temperature returns to normal.
Error 11: Check the wall tracking sensor.| If the wall tracking sensor is
covered by dust, wipe and clean it.
Error 12: Place the main unit on level ground and start it.| If the main unit
is detected to be tilted, place it on level ground and start it.

Error 13: Abnormal vacuum fan.

| If the vacuum fan does not work properly, reset the system.
If the alert continues, contact the customer service.
Error 14: Check if the top radar cover is stuck.| If the top radar cover is
stuck or under pressure, move the appliance to a new location and start it.
Error 15: Move the main unit away from forbidden areas and start it.| Move the
main unit away from the virtual walls or forbidden areas and start it.
Error 16: Cannot return to the charging dock. Remove any obstacles near the
charging dock.|

Remove any obstacles that are closer than 1.5 m from the front of the charging
dock.

Error 17: Dust bag is not in place.

| Check if the dust bag is installed.
If installed, check if it reaches the bottom of the charging dock.
If the alert continues, contact the customer service.

Error 18: Dust bag is full.

| If the dust bag is full, replace with a new one.
If the dust bag is not full, check if the dust collector’s channel is clogged.
If clogged, clean the dust channel.
If the alert continues, contact the customer service.
Error 19: Clean the dust box + water tank (2 in 1) if it has not been cleaned
for a long time.|

If there is excessive dust in the dust box + water tank (2 in 1), clean it and
the filter.

Error message

|

Solution

—|—
Error 20: Clean the filter.| Remove the filter and clean it.

Tip: Resetting the system can fix some errors.

FAQs

Question type

|

Solution

—|—

Cannot power on

| If the battery power is insufficient, dock the main unit on the charging
dock and fully charge it before next use. If the battery temperature is too
low or too high, use the product at temperatures of 0-40 °C.

Cannot charge

| Make sure both ends of the charging dock’s power cable are firmly plugged
in. If poor contact is detected, clean the charging contacts on the charging
dock and the charging plates on the main unit. Confirm if the charging
indicator turns on.

Slow charging

| When the product is used at extreme temperatures, to extend the battery
life, the main unit will automatically reduce the charging speed. If the
charging contacts are dirty, clean them with a dry cloth.

Cannot dock

| If there are many obstacles near the charging dock, place it in a clear,
open space. If the main unit is far away from the charging dock, place it near
to the charging dock and try again.
Abnormal operation| Restart the appliance.

Abnormal noises while cleaning

| If the main brush, side brush or driving wheel is entangled with debris,
turn off the appliance and clean. If the universal wheel is dusty or jammed
while cleaning, it is recommended to use a screwdriver to remove the wheel and
rinse it under water.

Decreased cleaning ability or dust falls out of the main unit

| If the dust box is full, clean the dust box. If the filter is clogged, clean
the filter. If the main brush is entangled with debris, clean the main brush.
Cannot connect to WiFi| If WiFi function is not activated, reset WiFi and try
again.
If WiFi signal is poor, place the main unit within the coverage of WiFi
signal.
If WiFi connection is abnormal, reset WiFi, download the latest mobile client
and try again.
If the APP does not support the current device model, follow the prompts to
check the models supported.
Cannot connect to WiFi suddenly. If the router settings are incorrect, contact
the customer service.
Scheduled cleaning does not start| Insufficient power. Scheduled cleaning will
only start when the power level is greater than 15%.

Is energy consumption high if the main unit is kept on the charging dock?

| Keeping the main unit on the charging dock helps to keep the battery at its
best performance, and the energy consumption is low.
Is it necessary to charge for 16 hours during the first three uses?| Lithium
batteries exhibit no memory effect. You may use the appliance when the battery
is full.

Mopping module discharges little or no water

| Check whether there is sufficient water in the water tank. Adjust the water
volume to Large via the APP. Make sure the mop and mop holder are installed
correctly according to the instructions.

Main unit does not resume cleaning after docking for charging

| Make sure the main unit is not in “Do Not Disturb” mode, in which the main
unit does not resume cleaning. It also does not resume cleaning if it is
docked by pressing the Dock button or manually returned to the charging dock.

Main unit does not return to charging dock after cleaning a localized area or
after being moved

| After cleaning a localized area or being moved far away, the robot vacuum
and mop cleaner will generate a new map. If the charging dock is far away, the
main unit may not automatically dock. In this case, manually return the main
unit back on the charging dock to charge.
Robot vacuum and mop cleaner misses spots| If the wall tracking sensor or edge
sensor is dirty, clean them with a soft dry cloth.

Technical data

“*” symbol indicates the product color, e.g. B = black, W = white, G = gray, P
= purple.

Product model

| China: DBS036A-2401200C ; United Kingdom: DBS036A-2401200B ; Korea: DBS036A-
2401200K ; United States: DBS036A-2401200U ; Japan: DBS036A-2401200J ;
European Union: DBS036A-2401200G ;| China: KA3601A-2401200CN ; United Kingdom:
KA3601A-2401200BS ; Korea: KA3601A-2401200KR ; United States: KA3601A-
2401200US ; Japan: KA3601A-2401200JP ; Australia: KA3601A-2401200AU ;

European Union: KA3601A-2401200EU ;

Product name| Power adapter| Power adapter
Rated input| 100-240V~, 50-60 Hz, 0.9 A| 100-240V~, 50-60 Hz, max. 1.0 A
Rated output| 24 V 1.2 A, 28.8 W| 24 V 1.2 A, 28.8 W

Product model

| China: DBS036A-2401200C ; United Kingdom: DBS036A-2401200B ; Korea: DBS036A-
2401200K ; United States: DBS036A-2401200U ; Japan: DBS036A-2401200J ;
European Union: DBS036A-2401200G ;| China: KA3601A-2401200CN ; United Kingdom:
KA3601A-2401200BS ; Korea: KA3601A-2401200KR ; United States: KA3601A-
2401200US ; Japan: KA3601A-2401200JP ; Australia: KA3601A-2401200AU ;

European Union: KA3601A-2401200EU ;

System requirements: Android 5.0 or later, iOS 10.0 or later (iPhone 5 or
later)
This product includes a WiFi module that supports the 802.11b/g/n transmission
protocol.
2.4GHz WLAN Module： SDJ01RM；Frequency Range：2400-2483.5MHz； Maximum
Transmitting Power：20dBm(EIRP)

Disposal

Correct disposal of this product

This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact the
retailer where the product was purchased. They can take this product for
environmental safe recycling.

Warranty and limitations of liability

This product is guaranteed for a period of 12 months (defined by local law)
from the date of purchase against any failure resulting from manufacturing or
material defects. This warranty does not cover damage caused by improper
installation, improper use, or normal wear and tear of the product.
More specifically, the warranty does not cover:

• Dust bag, disposable mop, side brush, filter, mop, main brush and main brush cover are not covered by the warranty as they are consumable items.
• Damage or problems caused by improper use, accident, alteration or electrical connection of improper intensity or voltage.
• Modified products, those whose warranty seal or serial number have been damaged, altered, removed or oxidized.
• Failure of the battery due to overcharging or failure to observe the safety instructions explained in the instruction manual.
• Cosmetic damage, including scratches, dents, or any other element.
• Damage caused by any intervention carried out by an unauthorised person.
• Defects caused by normal wear and tear or due to normal ageing of the product.
• Software updates due to a change in network settings.
• Product failures due to the use of third party software to modify, change or adapt the existing software.
• Product failures caused by use without accessories approved by the manufacturer.
• Oxidised products.

Terms and conditions of implementation
To obtain a warranty service, you are requested to return your product to the
customer service desk of your retail outlet with your proof of purchase
(receipt, invoice, …), the product and its supplied accessories, with its
original packaging.
It is important to have the date of purchase, the model and the serial or IMEI
number on hand as information (this information usually appears on the
product, the packaging or your proof of purchase).
Failing this, you must return the product with the accessories necessary for
its proper operation (power supply, adaptor, etc.).
In the event that your claim is covered by the warranty, the after-sales
service may, within the limits of local law, either:

• Repair or replace defective parts.
• Exchange the returned product with a product that has at least the same functionality and that is equivalent in terms of performance.
• Refund the product at the purchase price of the product mentioned on the proof of purchase.

If one of these 3 solutions is used, this does not give rise to the extension
or renewal of the warranty period.

Warranty card

Customer name|  | Product name and model|
—|—|—|—
Mailing address|  | Main unit serial number|
Contact information|  | Purchase date|

This warranty card contains customers’ personal information, keep it safe

Maintenance records

Servicing center| Fault description| Replacement parts| Servicing engineer|
Servicing date
—|—|—|—|—
 |  |  |  |
 |  |  |  |
 |  |  |  |
 |  |  |  |
 |  |  |  |

Manufacturer:ROIDMI INFORMATION TECHNOLOGY CO., LTD.

Address: 4F,C8 BUILDING,NO.1699 HUISHAN ROAD,LIFE SCIENCE AND TECHNOLOGY
PARK,HUISHAN DISTRICT, WUXI,JIANGSU,PRC Executive standards:
PPP 11005F: 2018,EN 50564:2011
EN 60335-1:2012/A2:2019,EN 60335-2-2:2010/A1:2013,EN 62233:2008
EN 55014-1:2017,EN 55014-2:2015,EN IEC 61000-3-2:2019,EN
61000-3-3:2013/A1:2019
EN 301 489-1 V2.2.3:2019,EN 301 489-17 V3.2.4:2020
EN 300 328 V2.2.2:2019,EN IEC 62311:2020,EN 50665:2017
2011/65/EU
Service email: wxrm@roidmi.com
Website:–
No.09.2021
Only applicable to the robot vacuum and mop cleaner model SDJ01RM / SDJ01RM*
Made in China

References

• Roidmi-ShowDoc
• ROIDMI Official | Robot Vacuum & Vacuum Cleaner – ROIDMI Offical Site

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>